EM510W

Hardware devices covered by this platform

RAM	16,128 bytes for application variables and data
Flash	262,144 bytes for application storage, data cannot be stored in this memory
EEPROM	2016 bytes for application data

TiOS Firmware Version	Date	Notes
V3.80.24 (download)	17SEP2020	Corrected behavior of yellow Status Ethernet LED Set auto-negotiation to 10/100Mbit/s by default
V3.80.18 (download)	18JUL2019	Initial release

Platform type	32-bit platform
Clock frequency (CLOCK) and clock control	Frequency is fixed at 24MHz
Available network interfaces	Ethernet (net.), Wi-Fi (wln.) , PPP (ppp.), PPPoE (pppoe.)(1)
GPIO type	Unidirectional(2)
UART limitations	Max practical baudrate ~460800 7 bits/NO PARITY mode should not be used
Serial port FIFOs	N/A
Serial port line configuration	Depends on the serial port mode
Serial port interrupts and io.intenabled	Interdependent
RTS/CTS remapping	Supported
ADC	NO
Pulse-width Modulation (PWM)	NO
GA1000 support	NO
WA2000 support	YES
WA2000 lines remapping	Not supported(3)
Beep.divider calculation	N/A (buzzer not supported)
Recommended buzzer frequency divider	N/A (buzzer not supported)
Display type selection and line remapping	Display not supported
Special configuration section of the EEPROM	32 bytes for MAC and device password storage
Device serial number	4 bytes, the number can't be changed
Flash memory configuration	Dedicated memory for firmware/application Data cannot be stored in this memory
Self-upgrades for the Tibbo-BASIC/C app.	Supported through fd.copyfirmware, fd.copyfirmwarelzo, fd.copyfirmwarefromfile, and fd.copyfirmwarefromfilelzo methods; Requires an externally connected flash IC
Status LEDs (LED Control Lines)	Green status (SG) LED control line Red status (SR) LED control line Patented Ethernet link status indication mechanism: LED brightness indicates link status
Debug communications	Ethernet / UDP Broadcast transport Ethernet /WinPCap transport

Comments:

The sock.allowedinterfaces property refers to the Ethernet interface as "NET", Wi-Fi — as "WLN", PPP — as "PPP", and PPPoE — as "PPPOE". Sock.targetinterface and sock.currentinterface properties rely on the pl_sock_interfaces enum, whose members differ depending on the platform.
Surrounding hardware may dictate which GPIO lines must be used as inputs and which — as outputs.
Connect the WA2000 as shown on Fig. B in Connecting GA1000 and WA2000):

bt — in charge of the BLE (Bluetooth Low-Energy) interface (requires the WA2000 add-on module);

button — monitors the MD (setup button) line;

fd* — manages the flash memory file system and direct sector access (requires an externally connected flash IC);

io — handles I/O lines, ports, and interrupts;

net — controls the Ethernet port;

pat — "plays" patterns on up to five LED pairs;

ppp — accesses the Internet over a serial modem (GPRS, etc.);

pppoe — accesses the Internet over an ADSL modem;

romfile — facilitates access to resource files (fixed data);

ser — controls the serial port (UART, Wiegand, clock/data modes);

sock — socket comms (up to 32 UDP, TCP, and HTTP sessions);

ssi — controls serial synchronous interface channels (SPI, I2C...);

stor — provides access to the EEPROM;

sys — in charge of general device functionality;

wln — handles the Wi-Fi interface (requires the WA2000 add-on module).

* Disabled by default — enable it in Project Settings -> Customize.

This platform supports the standard set of variable types and functions (a.k.a. "syscalls") except aes128enc and aes128dec.

You can find them here.