TPP3W-G2

Top  Previous  Next

Memory space and key info

RAM

66,816 bytes for application variables and data

Flash

786,432 bytes for application storage, and separately

1,048,576 bytes for data storage (dedicated flash disk memory)

EEPROM

2040 bytes for application data

 

Platform type

32-bit platform

Clock frequency (CLOCK) and clock control

Frequency is fixed at 120MHz

Available network interfaces

Ethernet (net.), Wi-Fi (wln.) , PPP (ppp.), PPPoE (pppoe.)(1)

GPIO type

Unidirectional(2)

UART limitations

Max practical baudrate ~460800

7 bits/NO PARITY mode should not be used

Serial port FIFOs

1 byte for TX, 1 bytes for RX

Serial port line configuration

Depends on the serial port mode

Serial port interrupts and io.intenabled

Interdependent

RTS/CTS remapping

Supported(3)

GA1000 lines remapping

Supported(4)

Beep.divider calculation

beep.divider=CLOCK / (4 * desired_frq)

Recommended buzzer frequency, divider

2700Hz, beep.divider = 11111

Display type selection and line remapping

Display not supported

Special configuration section of the EEPROM

28 bytes for MAC and device password storage

Device serial number

128 bytes: 64 OTP bytes + 64 fixed bytes

Flash memory configuration

Dedicated

Status LEDs /LED control lines

Green status (SG) LED

Red status (SR) LED

Yellow Ethernet status (EY) LED

An LED bar consisting of five blue LEDs

Debug communications

Ethernet / UDP Broadcast transport

Ethernet /WinPCap transport

 

Comments:

1.The sock.allowedinterfaces property refers to the Ethernet interface as "NET", Wi-Fi — as "WLN", PPP — as "PPP", and PPPoE — as "PPPOE". Sock.targetinterface and sock.currentinterface properties rely on the pl_sock_interfaces enum, whose members differ depending on the platform.
2.Surrounding board hardware and installed Tibbits dictate which GPIO lines must be used as inputs and which — as outputs.
3.Default CTS/RTS mapping is different for each serial port:

 

RTS

CTS

Port 1

0- PL_IO_NUM_0

0- PL_INT_NUM_0 (16- PL_IO_NUM_16_INT0)

Port 2

1- PL_IO_NUM_1

1- PL_INT_NUM_1 (17- PL_IO_NUM_17_INT1)

Port 3

2- PL_IO_NUM_2

2- PL_INT_NUM_2 (18- PL_IO_NUM_18_INT2)

Port 4

3- PL_IO_NUM_3

3- PL_INT_NUM_3 (19- PL_IO_NUM_19_INT3)

 

4.Although the platform itself supports remapping, actual "wires" connecting the system to the GA1000 are fixed and your mapping should reflect this:

 

CS

PL_IO_NUM_49

CLK

PL_IO_NUM_53

DI

PL_IO_NUM_52

DO

PL_IO_NUM_50

RST

PL_IO_NUM_51

 

Supported Objects, variable types, and functions

Sock — socket communications (up to 16 UDP, TCP, and HTTP sessions);
Net — controls the Ethernet interface;
Wln — handles the Wi-Fi interface (requires the GA1000 add-on module to be plugged into the TPP3 G2 board);
Ser — in charge of serial ports (UART, Wiegand, and clock/data modes);
Ssi  — implements up to four serial synchronous interface (SSI) channels, supports SPI, I2C, clock/data, etc.;
Io — handles I/O lines, ports, and interrupts;
Kp*— scans keypads of matrix and "binary" types;
Rtc — keeps track of date and time;
Fd — manages flash memory file system and direct sector access;
Stor — provides access to the EEPROM;
Romfile — facilitates access to resource files (fixed data);
Pppoe — provides access to the Internet over an ADSL modem;
Ppp**— provides access to the Internet over a serial modem (GPRS, POTS, etc.);
Pat — "plays" patterns on up to five LED pairs;
Beep — generates buzzer patterns using the onboard buzzer;
Button — monitors the onboard setup (MD) button;
Sys — in charge of general device functionality.

 

* On this platform, the kp. object will normally handle the 4-key sensor keypad, which is built into the size 2 Tibbo Project System with LCD/keys (TPS2L). The object can also be configured to communicate with an external keypad connected to the TPP3 G2 board via Tibbits (Tibbo sockets). Only one keypad can be serviced at a time.

** This may be an external modem connected to the TPP3 G2 board or a GPRS Tibbit module plugged into the board.

 

The TPP3W platform supports the standard set of variable types and functions (a.k.a. "syscalls").

 

Platform-specific constants

You can find them here.