EM1000 and EM1000W Platforms

Top Previous Next

The difference between the EM1000 and EM1000W platforms is that the EM1000W additionally includes the Wi-Fi (wln.) object (requires an external GA1000 add-on module). All other features of these two platforms are exactly the same.

Memory space

RAM	22,528* bytes for application variables and data
Flash	983,040 bytes for application and data storage (shared flash memory)**
EEPROM	2040 bytes for application data

*RAM available in the debug mode is smaller by 257 bytes. All memory is available in the release mode.

**Some earlier devices had only 458,752 bytes of flash memory available

Supported Objects, variable types, and functions

•Sock — socket communications (up to 16 UDP, TCP, and HTTP sessions);

•Net — controls the Ethernet interface;

•Wln — handles the Wi-Fi interface (only available on the EM1000W platform, requires GA1000 add-on module);

•Ser — in charge of serial ports (UART, Wiegand, and clock/data modes);

•Ssi — implements up to four serial synchronous interface (SSI) channels, supports SPI, I2C, clock/data, etc.;

•Io — handles I/O lines, ports, and interrupts;

•Lcd — controls graphical display panels (several types supported);

•Kp — scans keypads of matrix and "binary" types;

•Rtc — keeps track of date and time;

•Fd — manages flash memory file system and direct sector access;

•Stor — provides access to the EEPROM;

•Romfile — facilitates access to resource files (fixed data);

•Pppoe — provides access to the Internet over an ADSL modem;

•Ppp — provides access to the Internet over a serial modem (GPRS, POTS, etc.);

•Pat — "plays" patterns on up to five LED pairs;

•Beep — generates buzzer patterns;

•Button — monitors the MD line (setup button);

•Sys — in charge of general device functionality.

These platforms support the standard set of variable types and functions (a.k.a. "syscalls").

Platform-specific constants

You can find them here.

Miscellaneous information

Available network interfaces	EM1000: Ethernet (net.) EM1000W: Ethernet (net.), Wi-Fi (wln.)(1)
GPIO type	Unidirectional
RTS/CTS remapping	Supported(2)
GA1000 lines remapping	Supported(3)
Serial port FIFOs	16 byte for TX, 16 bytes for RX
Clock frequency (PLL) control	PLL on: 88.4736Mhz, PLL off: 11.0592Mhz(4)
Special configuration section of the EEPROM	8 bytes for MAC storage
Device serial number	128 bytes: 64 OTP bytes + 64 fixed bytes(5)
Flash memory configuration	Shared
LEDs	Green (SG) and red (SR) Status LED lines Green (EG) and yellow (EY) Ethernet LED lines
Debug communications	Ethernet / UDP Broadcast transport Ethernet /WinPCap transport

Comments:

1.The sock.allowedinterfaces property refers to the Ethernet interface as "NET", Wi-Fi -- as "WLN". Sock.targetinterface and sock.currentinterface properties rely on the pl_sock_interfaces enum, whose members differ depending on the platform.

2.Default CTS/RTS mapping is different for each serial port:

	RTS	CTS
Port 1	0- PL_IO_NUM_0	0- PL_INT_NUM_0 (16- PL_IO_NUM_16_INT0)
Port 2	1- PL_IO_NUM_1	1- PL_INT_NUM_1 (17- PL_IO_NUM_17_INT1)
Port 3	2- PL_IO_NUM_2	2- PL_INT_NUM_2 (18- PL_IO_NUM_18_INT2)
Port 4	3- PL_IO_NUM_3	3- PL_INT_NUM_3 (19- PL_IO_NUM_19_INT3)

3.Mapping of GA1000 control lines is fully flexible on the EM1000W. However, if the GA1000 module is installed on top of the EM1000 (so called EM1000G module combination), then the following mapping must be applied:

CS	49- PL_IO_NUM_49
CLK	53- PL_IO_NUM_53
DI	52- PL_IO_NUM_52
DO	50- PL_IO_NUM_50
RST	51- PL_IO_NUM_51

4.Default PLL state after the external reset depends on the PM pin of the EM1000(W).

5.Older EM1000 and EM1000W devices did not contain the serial number. To find out if your EM1000(W) has the serial number onboard, try to read this serial number with the sys.serialnum R/O property. If this property returns an empty string, then the serial number is not present. Sys.serialnum returns all 128 bytes of the serial number. First 64 bytes are one-time-programmable (OTP) with the sys.setserialnum method.