DS1206N

Top  Previous  Next

ds1206n

Introduction

The DS1206N is a BASIC-programmable board designed primarily for serial-over-IP and serial control applications. Being small enough to fit inside your product, the board offers a rapid development alternative to using modules, which require making new host PCB.

The DS1206N features a multi-channel serial port. The board has a single serial port connector and is priced as a single-port product, yet it packs four independent serial channels. Have no use for those DSR and DTR lines? Turn them into RX and TX of an additional serial channel. Don't want CTS and RTS either? That's one more channel! In total, there are 15 different configurations to choose from.

The board is supplied in three versions offering various serial port and power options (see below).

The DS1206N is fully supported by TIDE software and a dedicated DS1206 platform that covers all hardware facilities of the board (see "TIDE and Tibbo BASIC Manual").  This product ships preloaded with a fully functional serial-over-IP application. Written in Tibbo BASIC/C, the application is compatible with Tibbo Device Server Toolkit software, comes with full source codes, and can be modified by the user.

Available models

The board is supplied in three modifications.

The DS1206N-RS is, essentially, a DS1206 device without a housing. The board has a proper RS232 port (RS232 transceiver IC and DB9M connector), as well as the power regulator ("12V"-to-3.3V). There is also a power switch that controls "12V" power output on pin 9 of the DB9M connector.

The DS1206N-TM is different from the "-RS" version in that it has a TTL serial port and no power switch. The port is accessible through a 12-pin connector on the PCB. The power regulator of the board can be used to supply 3.3V power to the attached serial device as well.

Finally, the DS1206N-TS is like the "-TM" version but has no "12V"-to-3.3V power regulator. Instead, an attached serial device is supposed to provide stabilized 3.3V power to the board.

 

Available models and their features

DS1206N-RS

(RS232)

DS1206N-TM

(TTL master)

DS1206N-TS

(TTL slave)

Setup button

YES

Status LEDs

YES

RS232 transceiver & DB9M connector

YES

NO

TTL interface connector

NO

YES

Power switch

YES

NO

Power jack and "12V"-to-3.3V regulator

YES

NO

 

Hardware features

Superior upgrade to the EM1202EV board.

Based on a high-performance purpose-built 88-MHz T1000 ASIC.

10/100BaseT auto-MDIX Ethernet port (automatic detection of "straight" and "cross" cables).

Up to 3.5 serial channels:

 - DS1206N-RS: RS232 port (DB9M connector);

 - DS1206N-TM and "-TS": TTL serial port (pin header);

 - Baudrates of up to 921,600bps;

 - None/even/odd/mark/space parity modes;

 - 7/8 bits/character modes;

 - Full-duplex mode with optional flow control;

 - DS1206N-TM and "-TS": half-duplex mode with direction control;

 - Flexible mapping with 15 different options, such as:

    - A single channel: RX, TX, CTS, RTS, DSR, and DTR lines;

    - 3.5 channels: RX, TX, RX2, TX2, RX3, TX3, and RX4 lines.

- DS1206N-RS: optional "12V" power output on DB9M connector (software-controllable);

- DS1206N-TM: optional "12V" power input from the serial port (instead of supplying power through the power jack).

512KB or 1024KB flash memory for firmware, application, and data storage.

2KB EEPROM for data storage.

Four LEDs:

 - Green and red status LEDs on top of the device;

 - Link and speed Ethernet status LEDs on the RJ45 jack.

Software-controlled onboard PLL to select the clock frequency of the device: 11.0592MHz with PLL off, 88.4736MHz with PLL on.

Power:

 - DS1206N-RS and "-TM": onboard regulator, 10-24V input range (12V nominal);

 - DS1206N-TS: direct 3.3V input (must be regulated to +/- 5%).

Board dimensions: 52.6x38.0mm.

Firmware and Tibbo BASIC/C application are upgradeable through the serial port or network.

Tibbo BASIC/C application can be debugged through the network and no additional debugging hardware, such as in-circuit emulator, is required.

Also available as a DS1206 (DS1206N board with housing).

Programming features

Variable Types: Byte, char, integer (word), short, dword, long, real, string, plus user-defined arrays and structures.

Function Groups: string functions (27 in total!), date/time conversion functions (8), encryption/hash calculation functions (AES128, RC4, MD5, SHA-1), and more.

Platform objects:

 - Sock — socket communications (up to 16 UDP, TCP, and HTTP sessions);

 - Net — controls the Ethernet port;

 - Ser — in charge of serial channels;

 - Io — handles I/O lines, ports, and interrupts;

 - Fd — manages flash memory file system and direct sector access;

 - Stor — provides access to the EEPROM;

 - Romfile — facilitates access to resource files (fixed data);

 - Pat — "plays" patterns on green and red status LEDs;

 - Button — monitors the setup button;

 - Sys — in charge of general device functionality.